611 industrial way west, eatontown, nj 07724 tel: 732-460- 0212 fax: 732-460-0214 sales@advanced-control.com www.a dvanced-control.com each detector model contains: ? dc return ? rf bypass capacitor ? detector diode ? video protection diode features: ? microstrip or stripline compatible ? static protection ? high sensitivity ? small size ? easy mounting applications: ? transmitter monitoring ? radar equipment ? missile guidance systems ? input to low-noise amplifiers ? broadband or narrowband ecm receivers ? power and signal monitors ? doppler radar and beacon receivers ? matched units available for mult i-channel receivers, amplitude comparator systems and discriminators minimum (5) flatness nominal (3) frequency sensitivity vs typical (2) video standard optional range part (1) k frequency tss capacitance case case (ghz) number (mv/mw) (+/-db) (dbm) (pf) styles styles 0.95 - 1.25 acsm2036p 2000 0.2 -53 20 m51 m50 1 - 1.5 acsm2155p 1700 0.25 -52 75 m51 m50 2 - 6 acsm2030p 2000 0.3 -53 12 m51 m50 2 - 12 acsm2032p 2000 1.0 -52 12 m51 m50 2 - 18 acsm2031p 1700 1.3 -51 12 m51 m50 8 - 18 acsm2033p 1700 1.0 -51 12 m51 m50 12 - 18 acsm2034p 1800 0.75 -51 12 m51 m50 17 - 18 acsm2139p 1700 0.5 -51 9 m51 m50 notes: 1) standard output polarity is positive. if negative output is required, substitute ?n? for ?p? in part number. 2) tangential signal sensitivity (tss) is a measure of low level sensitivity with respect to noi se. it is measured using a vid eo amplifier with a 2mhz bandwidth and a 3db noise figure. 3) video capacitance is used for rf bypass. this value can be changed if required for video response time or other considerati ons. contact the factory if value other than those shown are needed. 4) video protection is available on most models. this feature helps to prevent damage to the detector diode from incidents occ urring at the video port. transient electromagnetic spikes, static contact, or voltage surges can ea sily damage a detector diode. a video p rotection diode will clamp the voltage at a value less than the detector break down voltage. note: inclusion of this protection will caus e the output voltage to compress and clamp. this occurs at about + 10dbm input to the detector. if operation above +10dbm is require d then the output protection should be modified or ex cluded. adding a suffix ?x? at the end of the model number will exclude the vide o protection feature. contact the factory for assistance. 5) standard bias is 100ua. 6) zero bias schottky ve rsions are available for most of listed biased schottky models with onl y minor differences in specifica tions. a. the zero bias schottky has an impedance of several thousand ohms. b. zero bias schottky detecto rs exhibit less sensitive tss due to the high diode impedance (typically a 3db reduction). c. the temperature performance of the zero bias schottky is poor when operating at low input power levels. this difference becomes small at high levels (above 0dbm input power). the part number of zero bias versions includes a ?z? following the polarity indicator. static protection and easy mounting are important features of these high sensitivity detectors. they offer excellent octave or broadband rf performance and rugged construction for harsh environments. the static protection virtually eliminates damage due to handling or from video transients. the bolt channel package allows for very simple and reliable screw-on mounting. the modified package saves additional space by elimi nating one thru hole. the standard output polarity is positive. negative output versions are available with slightly lower sensitivity. bolt channel schottky detectors
611 industrial way west, eatontown, nj 07724 tel: 732-460- 0212 fax: 732-460-0214 sales@advanced-control.com www.a dvanced-control.com environmental specifications: screening : mil-e-5400, mil-std-202, mil-e-16400 standard screening : operating temp: -65c to +125c internal visual per mil-std-883, method 2017 storage temp: -65c to +150c temperature cycle: -65c to +100c, 10 cycles humidity: mil-std-202f, m103, cond b op tional high-rel screening (ref mil-prf-38534) : shock: mil-std-202f, m213, cond b internal visual per mil-std-883, method 2017 altitude: mil-std-202f, m105, cond b stabilization bake per mil-std-883, method 1008 vibration : mil-std-202f, m204, cond b temperature cycle per mil-std-883, method 1010 thermal shock: mil-std-202f, m107, cond a c onstant acceleration per mil-std-883, method 2001 temperature cycle: mil-std-202f, m105c, cond d burn-in per mil-std-883, method 1015 maximum input power: +20dbm leak test per mil-std-883, method 1014 external visual per mil-std-883, method 2009 case style m50 case style m51 part number ordering information: example: acsm2033pzm51x20 acsm2033: bolt channel schottky detector, 8 - 18ghz p: positive output polarity z: zero bias version (omit for biased version) m51: package type x: no video protection (omit for inclusion of video protection) 20: 20pf custom output ca pacitance (omit for standard value) smbc-0205 0.004 x 0.020 min. (2) plcs. 0.020 max. (to flat) colored dot input 0.280.005 0.160 0.205.003 0.135.010 (2) plcs. ?0.096.003 thru 0.126.004 0.062.002 0.079.002 0.080.001 ?0.096.003 thru (2) plcs. 0.126.004 0.080.001 0.161.001 0.205.003 colored dot input 0.062.002 0.135.010 (2) plcs. 0.252.003 0.411.002 0.079.002 0.004 x 0.020 min. (2) plcs. 0.020 max. (to flat)
|
